温馨提示×

温馨提示×

您好,登录后才能下订单哦!

密码登录×
登录注册×
其他方式登录
点击 登录注册 即表示同意《亿速云用户服务条款》

linux命令ifconfig的详细解释

发布时间:2021-09-01 16:22:20 来源:亿速云 阅读:781 作者:chen 栏目:关系型数据库

这篇文章主要讲解了“linux命令ifconfig的详细解释”,文中的讲解内容简单清晰,易于学习与理解,下面请大家跟着小编的思路慢慢深入,一起来研究和学习“linux命令ifconfig的详细解释”吧!

许多windows非常熟悉ipconfig命令行工具,它被用来获取网络接口配置信息并对此进行修改。Linux系统拥有一个类似的工具,也就是ifconfig(interfaces config)。通常需以root身份登录或使用sudo以便Linux机器上使用ifconfig工具。依赖于ifconfig命令中使用些选项属性,ifconfig工具不仅可以被用来简单地获取网络接口配置信息,还可以修改这些配置。

1.命令格式:

ifconfig [网络设备] [参数]

2.命令功能:

ifconfig 命令用来查看和配置网络设备。当网络环境发生改变时可通过此命令对网络进行相应的配置

3.命令参数:
   


4.使用实例:

实例1:显示网络设备信息激活状态的

命令:

ifconfig

输出:

 

[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:50:56:BF:26:20  
          inet addr:192.168.120.204  Bcast:192.168.120.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8700857 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31533 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:596390239 (568.7 MiB)  TX bytes:2886956 (2.7 MiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:68 errors:0 dropped:0 overruns:0 frame:0
          TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:2856 (2.7 KiB)  TX bytes:2856 (2.7 KiB)

 

eth0:网卡的代号。

Link encap(encapsulation [inkpsju'lein;inkps'lein] n. 封装,包装,密封):Ethernet 以太网。
HWaddr:网卡的硬件地址,习惯称为MAC。
inet addr:IPv4的IP地址,后续的Bcast、Mask分别代表的是Broadcast和Netmask。
inet6 addr:是IPv6的版本的IP,我们没有使用,所以略过  scope:域
RX:那一行代表的是网络由启动到目前为止的数据包接收情况,packets代表数据包数、errors代表数据包发生错误的数量、dropped代表数据包由于有问题而遭丢弃的数量等。
TX:和RX相反,为网络由启动到目前为止的传送情况。
collisions:代表数据包碰撞的情况,如果发生太多次,表示你的网络状况不太好。
txqueuelen:代表用来传输数据的缓冲区的储存长度。
RX Bytes、TX Bytes:总传送、接收的字节总量。
Interrupt、Memory:网卡硬件的数据,IRQ岔断和内存地址。
通过观察上述的资料,大致上能了解到你的网络情况,尤其是RX、TX内的error数量,及是否发生严重的collision情况,都是需要注意的。

说明:

eth0 表示第一块网卡, 其中 HWaddr 表示网卡的物理地址,可以看到目前这个网卡的物理地址(MAC地址)是 00:50:56:BF:26:20

inet addr 用来表示网卡的IP地址,此网卡的 IP地址是 192.168.120.204,广播地址, Bcast:192.168.120.255,掩码地址Mask:255.255.255.0 

lo 是表示主机的回坏地址,这个一般是用来测试一个网络程序,但又不想让局域网或外网的用户能够查看,只能在此台主机上运行和查看所用的网络接口。比如把 HTTPD服务器的指定到回坏地址,在浏览器输入 127.0.0.1 就能看到你所架WEB网站了。但只是您能看得到,局域网的其它主机或用户无从知道。

第一行:连接类型:Ethernet(以太网)HWaddr(硬件mac地址)

第二行:网卡的IP地址、子网、掩码

第三行:UP(代表网卡开启状态)RUNNING(代表网卡的网线被接上)MULTICAST(支持组播)MTU:1500(最大传输单元):1500字节

第四、五行:接收、发送数据包情况统计

第七行:接收、发送数据字节数统计信息。


实例2:启动关闭指定网卡

命令:

ifconfig eth0 up

ifconfig eth0 down

输出:

说明:

ifconfig eth0 up 为启动网卡eth0 ifconfig eth0 down 为关闭网卡eth0ssh登陆linux服务器操作要小心,关闭了就不能开启了,除非你有多网卡。

 

 

实例3:为网卡配置和删除IPv6地址

命令:

ifconfig eth0 add 33ffe:3240:800:1005::2/64

ifconfig eth0 del 33ffe:3240:800:1005::2/64

输出:

说明:

ifconfig eth0 add 33ffe:3240:800:1005::2/64 为网卡eth0配置IPv6地址

ifconfig eth0 add 33ffe:3240:800:1005::2/64 为网卡eth0删除IPv6地址

练习的时候,ssh登陆linux服务器操作要小心,关闭了就不能开启了,除非你有多网卡。

 

实例4:用ifconfig修改MAC地址

命令:

ifconfig eth0 hw ether 00:AA:BB:CC:DD:EE

输出:

[root@localhost ~]# ifconfig eth0 down //关闭网卡
[root@localhost ~]# ifconfig eth0 hw ether 00:AA:BB:CC:DD:EE //修改MAC地址
[root@localhost ~]# ifconfig eth0 up //启动网卡
[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:AA:BB:CC:DD:EE  
          inet addr:192.168.120.204  Bcast:192.168.120.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8700857 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31533 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:596390239 (568.7 MiB)  TX bytes:2886956 (2.7 MiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:68 errors:0 dropped:0 overruns:0 frame:0
          TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:2856 (2.7 KiB)  TX bytes:2856 (2.7 KiB)
[root@localhost ~]# ifconfig eth0 hw ether 00:50:56:BF:26:20 //关闭网卡并修改MAC地址 
[root@localhost ~]# ifconfig eth0 up //启动网卡
[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:50:56:BF:26:20  
          inet addr:192.168.120.204  Bcast:192.168.120.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8700857 errors:0 dropped:0 overruns:0 frame:0
          TX packets:31533 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:596390239 (568.7 MiB)  TX bytes:2886956 (2.7 MiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:68 errors:0 dropped:0 overruns:0 frame:0
          TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:2856 (2.7 KiB)  TX bytes:2856 (2.7 KiB) 

说明:

 

 

实例5:配置IP地址

命令:

 

输出:

 

[root@localhost ~]# ifconfig eth0 192.168.120.56 
[root@localhost ~]# ifconfig eth0 192.168.120.56 netmask 255.255.255.0 
[root@localhost ~]# ifconfig eth0 192.168.120.56 netmask 255.255.255.0 broadcast 192.168.120.255

 

说明:

ifconfig eth0 192.168.120.56 

给eth0网卡配置IP地192.168.120.56

 ifconfig eth0 192.168.120.56 netmask 255.255.255.0 

给eth0网卡配置IP地址192.168.120.56 并加上子掩码255.255.255.0

ifconfig eth0 192.168.120.56 netmask 255.255.255.0 broadcast 192.168.120.255

/给eth0网卡配置IP地址192.168.120.56加上子掩码255.255.255.0加上个广播地址 192.168.120.255

 

 

实例6:启用和关闭ARP协议

命令:

ifconfig eth0 arp

ifconfig eth0 -arp

输出:

 

[root@localhost ~]# ifconfig eth0 arp 
[root@localhost ~]# ifconfig eth0 -arp

 

说明:

ifconfig eth0 arp 开启网卡eth0 arp协议;

ifconfig eth0 -arp 关闭网卡eth0 arp协议;

 

 

实例7:设置最大传输单元

命令:

ifconfig eth0 mtu 1500

输出:

 

[root@localhost ~]# ifconfig eth0 mtu 1480
[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:50:56:BF:26:1F  
          inet addr:192.168.120.203  Bcast:192.168.120.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1480  Metric:1
          RX packets:8712395 errors:0 dropped:0 overruns:0 frame:0
          TX packets:36631 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:597062089 (569.4 MiB)  TX bytes:2643973 (2.5 MiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:9973 errors:0 dropped:0 overruns:0 frame:0
          TX packets:9973 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:518096 (505.9 KiB)  TX bytes:518096 (505.9 KiB)

[root@localhost ~]# ifconfig eth0 mtu 1500
[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:50:56:BF:26:1F  
          inet addr:192.168.120.203  Bcast:192.168.120.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:8712548 errors:0 dropped:0 overruns:0 frame:0
          TX packets:36685 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:597072333 (569.4 MiB)  TX bytes:2650581 (2.5 MiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:9973 errors:0 dropped:0 overruns:0 frame:0
          TX packets:9973 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:518096 (505.9 KiB)  TX bytes:518096 (505.9 KiB)

[root@localhost ~]# 

 

说明:

设置能通过的最大数据包大小为 1500 bytes

 

备注:用ifconfig命令配置的网卡信息,在网卡重启后机器重启后,配置就不存在。要想将上述的配置信息永远的存的电脑里,那就要修改网卡的配置文件了。

感谢各位的阅读,以上就是“linux命令ifconfig的详细解释”的内容了,经过本文的学习后,相信大家对linux命令ifconfig的详细解释这一问题有了更深刻的体会,具体使用情况还需要大家实践验证。这里是亿速云,小编将为大家推送更多相关知识点的文章,欢迎关注!

向AI问一下细节

免责声明:本站发布的内容(图片、视频和文字)以原创、转载和分享为主,文章观点不代表本网站立场,如果涉及侵权请联系站长邮箱:is@yisu.com进行举报,并提供相关证据,一经查实,将立刻删除涉嫌侵权内容。

AI